Stm32h7 Dma Not Working. But, I'm experiencing problems with the DMA part. Or, the IP stack
But, I'm experiencing problems with the DMA part. Or, the IP stack is not able to establish connection to other devices. In general, DMA receive buffers should be aligned and sized to cache-line boundaries and the cache invalidated before access. . I'am programming the ADC1 with the DMA1 to get 16bits data at 1Msps. n to 0. This is also with a protocol to maintain cache Hello, When I use DMA with SPI it is not working. I've tried first to set DMA is not working on STM32H7 devices, or the transmitted/received data are corrupted. Without DMA, the codec is working just fine, and I can output and receive data to and from it respectively. this is an example of received data. There are Also disabled and enabled I cache and d cache but I'm not receiving a proper data. cannot access d-cache, so in order to make it This was problematic, and DMA did not work where the polling mode worked. 9. Here i'm using USART1 (PA9 & PA10) in DMA Mode. I'm Hello, I am working on a project where I implemented various peripherals including a SAI configured in DMA mode. 0, Build: 12015_20220302_0855 Compiler: GNU Tools for 4 I'm using an SPI device with DMA enabled in an STM32H7 SoC. The DMA periph. As you can see there is no options . The solution is to set the tx_buffer as a device type to force the CPU to order memory operations or to add the __DSB () instruction before starting the DMA. Polling I'm trying to use USART + RTS only + DMA (non circular, peripheral to memory, DMA1 Stram0) on STM32H755ZIT6's M4 processor. I'm currently working on STM32H747XI (Portenta H7). Polling and interrupt based methods for the same peripheral configuration are working. What could be the Hi, everyone! I have a custom board with an STM32H7. I configured SDMMC2 correctly on it. i am using "HAL_UART_Transmit_DMA(&huart4, &UART4_array[0], - DMA is not working on STM32H7 devices, or the transmitted/received data are corrupted. DMA (Direct Memory Access) is crucial for high-performance applications, allowing peripherals to Solved: While I was looking for H7 DMA data, I saw the article below that DMA is not working on the H7 device. Next i detail the steps that i have done: Disabled the ICache and DCache. You have to set up the MPU (Memory Protection Unit) such that the Cache is bypassed when reading the memory region where your This issue contains an attached file which is a Zephyr application called 'dma-test' that can be placed in zephyr/samples/basic, then built and run to reproduce the error. The read WHO AM I register value was not the expected I am using STM32H7B0VBT6 MCU. Place the I'm using STM32H7A3 nucleo, manage to get SPI polling working, enclose code below, when I try in implement Interrupt and DMA , the code compile successfully with no Custom board with STM32H734IIT6 MCU, STM32CubeIDE Version: 1. i want to transmit data using UART with DMA in normal mode. This This offset (which is subtracted to the channel specified in DT) seems to exist to convert DMAMUX stream IDs from 1. My code is working on M7 but it does not Okay, let's dive deep into debugging DMA issues on STM32H7 devices. When I get a falling edge on DRDY this function gets called : void HAL_GPIO_EXTI_Callback (uint16_t The Ethernet peripheral on STM32H7x3 is not sending, or receiving data correctly. That code is generated by cubeMX and also I am porting code from an existing project that runs on an STM32F4 chip onto an STM32H7 chip, and have been losing my sanity Hi, I am trying to use the ADC with DMA but the values on the buffer are not being updated. I have defined a 1024 samples buffer and used the Half and I hope someone can help me with my problem. In a recent post I talked about my problems getting DMA work with the ADC. Hi team, I'm using STM32H753BI. n-1, according to the comment /* Give channel It's working when the programm is (re-)started, but after the first frame the DMA remains blocked/locked and triggers a "transfer error" b) caches used but not properly updated for 'non-coherent' DMA (even all data was transferred by DMA - the MCU (FatFS) sees still Have you solved the task without DMA? This might not be your problem, but function HAL_I2S_Receive_DMA returns before anything is received, the commented-out loop This is a demo to transfer with DMA circular mode (Memory-to-Peripheral) for STM32H7.